Virtual Workshop: nTop Essentials & Toolkit Training on Thursday, December 3. Register now!

Topology Optimization for a Bicycle Wheel

This is the first of a series of blogs (and presentations) focusing on Design for Additive Manufacturing in the context of Industrial Design. This blog explores topology optimization for a bike wheel focusing on three mutually perpendicular loads: radial loads, tangential loads, and lateral loads.

Dan Martin
October 22, 2020

Introduction

The modern bicycle wheel is a uniquely efficient structure comprised of tension-compression members to maximize structural rigidity. The modern concept of the bicycle wheel has its roots in the traditional compression wheel, the design of which still has its place in many applications today including most modern cars and a wide variety of motorcycles. 

The optimization of compression wheels can significantly increase performance as a result of low rotational inertia while adequately distributing stress subject to a variety of distinct load cases. A bicycle was taken as just one embodiment of how this can be achieved through topology optimization.

In this study, the geometry of a compression style bicycle wheel was optimized using nTopology’s topology optimization algorithms to generate forms which efficiently distribute stress. Geometry was optimized for maximum stiffness at a set volume ratio subject to multiple distinct load cases. Data from literature is used to form a set of distinct load cases which were used to drive the topology optimization process. The resulting geometry was then assessed against the original load cases through finite element analysis to ascertain its efficacy and a scale model was created.

Setting up the model

A well-designed wheel should be able to adequately resist three mutually perpendicular loads: radial loads, tangential loads, and lateral loads. Two distinct complex load cases were considered:

  • Hard braking, consisting of Radial loads (FR) and Tangential loads (FT)
  • Lateral skid, consisting of Radial loads (FR) and Lateral loads (FL)

The design region considered for this study was based on a right angled section of a tapered disk. This model is further subdivided into another four sections to simulate a rolling contact patch across the wheel rim. Symmetry is enforced across the vertical plane and mid planes of the wheel section. The topology optimization is programmed to minimize the volume fraction while maximizing the model stiffness for each load case. The forces were modelled as acting uniformly over the contact patch as shown in the figure below.

Fig.1: Derivation of Forces applied to the contact patch

Results

The optimum wheel geometry differed depending on the applied load cases. As a result, the ideal wheel geometry is highly dependent on the relative magnitude of the various load cases considered, making it very difficult to find a solution through traditional analytical means. 

Using nTop Platform, outcomes could be easily investigated by simply varying the input parameters and iteratively running the same nTop workflow. The image below illustrates the evolution of optimum geometries by considering combinations of distinct load cases.

 

Fig.2: Comparison of optimized geometry for isolated load cases and contribution to complex load case solutions. From left to right: Simple Load Case, Complex Load Case, Combined Complex Load Case

Once a satisfactory model is created, the topology optimization result is converted into a solid model and smoothed. It was found that in most cases, rough symmetry about the 45°angle naturally occurred as a result of symmetric loading conditions. This geometry is isolated through an intersection with a 45° wedge and radially patterned to produce the full wheel body. The figure below gives a graphical representation of how the model of the full wheel was constructed.

Fig.3: Illustration of workflow

After the optimized geometry was patterned into a full wheel model, the resulting geometry was analyzed using finite element analysis to determine its effectiveness of stress distribution subject to complex combinations of load cases and was programmed within the same nTop Workflow. 

It was found that the relative magnitudes of maximum stress subject to complex load cases typically found during the scenarios of front wheel skid and hard braking were within 0.6MPa. This finding illustrates that the resulting geometry is equally efficient at distributing stress when subjected to the unique set of load cases associated with lateral skids and hard braking.

Fig.4: Finite element analysis of the model outcome

Conclusion

nTop Platform proved to be an effective and adaptive tool for the creation of efficient geometries when catering for multiple (sometimes complex) load cases. The bicycle wheel was an excellent example of this, where distinct load cases generate different optimized geometries and the most efficient geometry for the combined load case cannot easily be deduced through analytical means. The basic analysis discussed in this article can easily be adapted to find optimal geometries for wheels of varying sizes as well as different load cases.

To get a more in-depth understanding of this project please watch my presentation in the Design for Additive Manufacturing for Industrial Design eSeries on October 27.

Written by
After years of experience designing award-winning personal mobility devices in his hometown of Cape Town, South Africa, Dan Martin traveled to the US to further his studies on a Fulbright Scholarship. He now holds a bachelor’s degree in Electro-mechanical Engineering from the University of Cape Town and a master’s degree in Mechanical Engineering from Rochester Institute of Technology. At RIT, his studies focused on additive manufacturing with particular interest in potential applications for the future of transportation. He looks forward to using topology optimization as a powerful tool to inform the design process of future projects.

Up Next

Design for Additive Manufacturing (DfAM) for Industrial Design Speaker Series

Our latest series of presentations by experts in the field exploring industrial design applications for additive manufacturing using computational design tools.

Duann Scott
Texturing for Additively Manufactured Products with nTop Platform

From the subtle stipple of your laptop’s casing of to the geometric grip of your toothbrush handle, texture is a key consideration in the design process for any and every physical product. Read further to learn how I use nTop Platform to apply texturing to products I design.

Alex Ju